Daedalus DS-1010 M AC – Manual Pushable Scissor Lift with 10m Working Height

Introduction

DAEDALUS® Manual Pushable Scissor Lifts are an Economical Worksite solution without any compromise on the machine’s safety. These scissor lifts are Manually Maneuverable while their raising & lowering operations can be performed by AC / Battery Power Source as per your requirement. These machines are equipped with Pull out Screw Jack Stabilizers that enable them to level the machines. The solid Tyres on these machines enable you to utilize these machines in all conditions. These machines exhibit Least Downtime and require Minimum maintenance, thus enhancing your onsite Productivity.

Features:

1. Optional Power Source (AC / Battery Pack)
2. Anti-Skid Platform.
3. Foldable Guardrails (Optional).
4. Dual Control
5. Forklift Pockets

Safety Systems:

1. Manual Stabilizers
2. Max. Height cut off Switch
3. Flashing Beacon
4. Manual emergency relief valve

Specification

Models		DS-1010M/AC
Measurements		Feet	Metric
Maximum Working Height*		32ft	10m
Maximum Platform Height		26ft	8m
Lowered Platform Height		4.8ft	1.5m
Platform Length -		6.9ft	2.1m
Platform Width		3.9ft	1.2m
Guardrail Height		3.2ft	1.0m
Vehicle Dimensions	Length	8.5ft	2.5m
	Height	6.9ft	2.15m
	Width	3.9ft	1.2m
Ground Clearence		0.3ft	90mm

Productivity

Maximum Occupancy***	2 People
Lift Capacity	350Kgs
Control	Dual Control (Chassis & Platform)
Drive	NA

Power

Power Source	24V DC (Four 6V 225Ah Batteries) / 230V 50Hz Single Phase Supply
Hydraulic Capacity	20L (5.2gal)
Weight***	2200Kgs/1900Kgs

Benefits of the DS-1010 M/AC

▸ 10m Working Height Without a Self-Propelled Drive System

The DS-1010 M/AC reaches a 10m working height - matching some self-propelled scissor lifts - while remaining manually repositionable. For facilities that need height access to 10m but do not require the machine to travel under power (fixed-location maintenance tasks, production line overhead work), this eliminates the cost and operator competency requirements of a driven MEWP without sacrificing working height.

▸ Dual AC and Battery Power - Eliminates Generator Dependency

The machine accepts 230V single-phase AC supply directly from a wall socket, or 24V DC from the on-board battery pack. This is important at 10m where work sessions are typically longer: battery mode gives around a full shift of lift cycles on a charge; AC mode removes the battery concern entirely on sites with mains access. No diesel generator or separate power supply is required.

▸ 350 kg Platform Capacity at Full Height

At 10m, maintaining a 350 kg platform rating is a practical requirement for any task involving two operators and materials. The DS-1010 M/AC delivers this consistently - whether you are working on HVAC ducting, structural inspections, cable management, or overhead lighting systems. The 2.1m x 1.2m platform provides enough working area for both operators without feeling cramped.

▸ Screw-Jack Stabilisers - Essential at 10m Working Heights

At 10m elevation, even slight machine lean becomes magnified. The DS-1010 M/AC's pull-out screw-jack stabilisers must be deployed before raising to full height, locking the machine firmly on any surface. This is a deliberate design choice - the stabilisers are a mandatory safety step, not an optional accessory, and they ensure platform stability throughout the full work cycle.

▸ CE Certified to EN 280 - Verified Performance at the 10m Specification

CE certification to EN 280 covers the complete range of safety and performance parameters for MEWPs - including structural load testing at rated capacity, stability testing, and safety system verification. At 10m working height, this certification is particularly important: it confirms the machine has been tested and verified at its full operating height, not just at lower heights. This supports EHS compliance documentation under India's Factories Act 1948.

▸ Maximum Height Cut-Off Switch - Prevents Over-Extension

A mechanical height cut-off switch limits platform travel to the rated working height, preventing any possibility of over-extension through operator error. At 10m, this is a meaningful safety safeguard - especially given that the machine is often operated by maintenance personnel who may use different equipment types across their work week.

▸ Lower Whole-Life Cost Than a Self-Propelled Equivalent

Without a hydraulic drive system or drive motor to maintain, the DS-1010 M/AC has fewer serviceable components and lower expected maintenance costs than a self-propelled machine of comparable height. Solid tyres eliminate puncture callouts. The manual push mechanism has no electronic control complexity. For facilities with predictable, location-specific maintenance needs, this translates to a more economical ten-year total cost of ownership.

FAQs